Skip to content
Home » House Cleaning Services » End of a Lease: Cleaning Tips for Walls and Floors

End of a Lease: Cleaning Tips for Walls and Floors

Because dirty walls and floors are among the first things landlords and property inspectors look at, the risks of tenants losing their bonds are always high. If certain areas contain scuff marks, stains, spots, or mildew as a result of the renter’s negligence when cleaning, you could lose part or all of the security deposit you paid at the start of the tenancy. 

If the weekly rent is $700 or less, a rental bond in Sydney can be up to four weeks of rent. There is no maximum rental bond if the rent is more than $700. As a result, it’s a significant sum, and you should pay special attention to the walls and floors during the end-of-lease cleaning.

One of the greatest ways to ensure you get a complete rental bond payback is to hire expert bond cleaners in Sydney. If you want to clean yourself, here is an end-of-lease cleaning checklist with tips for washing the walls and floors. 

Look for any repairs or maintenance work that needs to be done

Before you begin the bond cleaning process, evaluate your home’s walls and floors for any repairs or maintenance work. Scrubbing or washing a broken or damaged surface might cause it to become even worse. 

As a result, if you discover cracks, paint chipping, a raised floor, or any other problem that isn’t your fault, notify the landlord and have it addressed. After you’ve completed the repairs, you can concentrate on cleaning stains from the walls and flooring. 

In addition, determine if the walls can be cleaned back to their original state, as a fresh paint job may be required in some circumstances. It can happen when these surfaces are peeling due to water damage or seepage.

Remove mould on the wall

In rooms with insufficient ventilation or persistently damp air, mould patches are frequent. As a result, they can be found on the walls and floors of the bathroom, kitchen, and laundry room, among other places. 

These defects not only detract from the appearance of the room but also contaminate the air quality and jeopardize the structural integrity of the surfaces. As a result, while doing end-of-lease cleaning, get rid of them fast.

You can spray white vinegar on the affected region and let it on for at least an hour. To eliminate the spots, clean the area with warm water and soap, then wash.

Furthermore, always clean at least 50 cm from the edge of the spots while scrubbing moldy regions. This area may contain mould spores that are undetectable to the naked eye and aid in mould regrowth. To avoid mould regrowth, make sure the clean surface is dry and the room is well aired.

Note: Vinegar should not be used on natural stones because it can erode and ruin the surface, resulting in irreversible damage. White vinegar’s acetic acid can damage a natural stone’s porous surface, which you can’t repair.

Vacuum

To eliminate dust, cobwebs, trash, and other physical contaminants, vacuum your entire house’s walls and floors. Cleaning the walls first, from top to bottom, is a professional bond cleaning approach used in Sydney to ensure that the cleaned areas remain contaminant-free.

To manage the task successfully and efficiently, make a ‘W’ pattern while cleaning the floors. To achieve the best results, move the cleaner straight ahead, then tilt it at a 45o angle and pull back.

Clean the Spot Clean The Areas

After vacuuming, concentrate on removing spots, stains, and marks from the walls and floors to properly sanitize them. A multi-surface cleaner, microfiber cloths, sponges, and a soft-bristled brush are required for this task.

Test the cleaner on an inconspicuous area before using it to make sure it won’t harm anything. It’s a bond cleaning in Sydney expert trick to avoid damaging the surfaces of the rental houses they clean.

Divide the floor into four quadrants and clean from the center to the perimeter during spot cleaning. When washing the walls, though, begin at the top and work your way down.

Use a microfiber mop to clean the walls

After spot cleaning, wipe down the walls with a microfiber mop to ensure they are clear of dust and debris. To completely remove smudges, fingerprints, or smatters, dampen the mop with a mild cleanser. Keep windows and doors open while washing walls to ensure that the room is sufficiently aired and the walls are dry.

Floors should be swept and mopped

While doing end-of-lease cleaning, the last thing you should do before leaving the rental property is sweep and mop the floors. Start cleaning the house’s innermost rooms first, then work your way outwards, finishing with the mudroom or entryways. 

To avoid recontaminating cleansed areas, many professional bond cleaners in Sydney use this procedure. A broom or a dry microfiber sweeper can be used to remove dust, filth, and debris from floors. 

Additionally, dampen microfiber mops with a floor cleaning/disinfectant solution while mopping floors. You can buy a commercial cleanser or make your own using 50 percent water, 50 percent white vinegar, and two teaspoons of mild detergent.

Conclusion

To receive your bond back in full, make sure your rental property’s walls and floors are clean for the final inspection. You can employ professional Sydney bond cleaners to thoroughly clean your rental home.

If you’re cleaning yourself, utilize the above-mentioned end-of-lease cleaning checklist for walls and floors. It also includes cleaning suggestions to make the procedure go more smoothly.

Â